Ormino 2212 920kv Brushless Motor F330 F450 F550 9443 Quadcopter Propeller 9450 RC Drone Accessories Profissional Propeller

Ormino 2212 920kv Brushless Motor F330 F450 F550 9443 Quadcopter Propeller 9450 RC Drone Accessories Profissional Propeller
  • Продавецwww.flimmer.com
  • Список ценUS $31.13piece
  • Продажная ценаUS $31.13piece
  • ДоставкаБесплатная доставка
  • Рейтинги3,2 (247)

Oписание продукта

 

 
 

 

Description:

Features:
Built from quality glass fiber and polyamide nylon.
Integrated PCB connections for direct soldering of your ESCs
Pre-threaded brass sleeves for all of the frame bolts.
Colored arms for orientation to keep you flying in the right direction.
Large mounting tabs on main frame bottom plate for easy camera mounting.
Easy assembly.

 

Specs:
Width: 450mm
Height: 55mm
Weight: 280g (w/out electronics)
Motor Mount Bolt Holes: 16/19mm

G.Weight: 395g

 

Wheelbase: 17.7in/450mm

Net weight: 272g

 

Made by advanced engineering material,super strong & smooth

Kit(need you assemble yourself)

100% Brand new 

 

APM V2.8.0 Flight Controller Upgrade Verstion 2.6 2.5.2 
APM V2.8.0 description:
- This version eliminates the 1.0mm 6P SM06B GPS interface of V2.52 old version, and change it into DF13-4P I2C external compass interface.
- Put DF13-5P GPS interface with external compass interface, convenient for the connection of GPS and externalcompass.
- V2.52 I2C interface changes to multifunctional MUX interface
- Modified version added isolation resistor, when the OSD interface used with telemetry, the interfaces is effectively avoided
- V2.52 version 3.5V power supply adopts IPS79133, 6V withstand voltage, output current 100mA, need to supply power for six IC, slightly inadequate power supply ability, easy to be burnt dwon. The new version adopts US LP2985-3.3, 16V withstand voltage, more reliable, redcucing the possibility of Bad Gyro health
APM V2.8.0 Flight Controller      
- Needle: staight
- Power supply: LP2985-3.3
- Max voltage: 16V
- Add a 47uF tantalum capacitor
- Port: MUX (UART0, UART2, mnnI2 and OSD are optional, OSD is the defaulted output)
Jumper cap choose:
- Built-in compass: plug the jumper cap in the MAG pin header.
- External compass: pull up the jumper cap from the MAG pin header.
 
 
30A SimonK Prgramme RC Brushless ESC With BEC 3A 
 
ESC Specification
 
Highest efficiency 100% N-FET design.
Highest accuracy with Crystal Oscillator (Temperature won\'t affect the PWM operating range like other cheap ESC\'s).
No low voltage cutoff, because any cutoff in a multirotor = crash.
No over temp cutoff, because any cutoff in a multirotor = crash.
Super high refresh rate, no buffering of the input signal, resulting in more than 490Hz response rate.
16KHz motor frequency, giving fastest response of the motor, and quietest operation as well (no 8KHz squeal).
Super simple, foolproof operation! Nothing to program other than the throttle range.
 
ESC Specs:
Cont. current: 30A
Max. current: 35A
Input Voltage: 2-4S lipo / 4-12 cell Ni-MH/Ni-Cd
BEC: 5V 2A (Linear mode)
Size: 55x26x8mm (length 145mm including power cable)
Weight: ~24g
 
 
NEO-M8N Flight Controller GPS Module with Shell 
 
 
 
A new generation Ublox GPS NEO-M8N,with low power consumption and high precision, the ultimate accuracy is 0.6 meters, actually almost 0.9 meters, greater than the previous generation NEO-7N 1.4-1.6 meters accuracy,support GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol and mode or more.
 
GPS Chip parameters:
 Receiver type 72-channel u-blox M8 engine
 GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1
 SBAS L1 C/A: WAAS, EGNOS, MSAS
 Galileo-ready E1B/C (NEO-M8N)
 Nav. update rate1 Single GNSS: up to 18 HZ
 Concurrent GNSS: up to 10 Hz
 Position accuracy2 2.0 m CEP
 Acquisition2 Cold starts: 26 s
 Aided starts: 2 s
 Reacquisition: 1.5 s
 Sensitivity2 Tracking & Nav: –167 dBm
 Cold starts: –148 dBm
 Hot starts: –156 dBm
 Assistance AssistNow GNSS Online
 AssistNow GNSS Offline (up to 35 days)3
 AssistNow Autonomous (up to 6 days)
 OMA SUPL & 3GPP compliant
 Oscillator TCXO (NEO-M8N/Q),
 Crystal (NEO-M8M)
 RTC crystal Built-In
 Noise figure On-chip LNA (NEO-M8M). Extra LNA for
 lowest noise figure (NEO-M8N/Q)
 Anti jamming Active CW detection and removal. Extra
 onboard SAW band pass filter (NEO-M8N/Q)
 Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N)
 Supported antennas Active and passive
 Odometer Travelled distance
 Data-logger For position, velocity, and time (NEO-M8N)
 
Operating temp. –40° C to 85° C
 Storage temp. –40° C to 85° C (NEO-M8N/Q)
 –40° C to 105° C (NEO-M8M)
 RoHS compliant (lead-free)
 Qualification according to ISO 16750
 Manufactured and fully tested in ISO/TS 16949 certified production sites
 Uses u-blox M8 chips qualified according to AEC-Q100
 
Supply voltage 1.65 V to 3.6 V (NEO-M8M)
 2.7 V to 3.6 V (NEO-M8N/Q)
 Power consumption4 23 mA @ 3.0 V (continuous)
 5 mA @ 3.0 V Power Save Mode
 (1 Hz, GPS mode only)
 Backup Supply 1.4 to 3.6 V
 
NEO-M8N-0 u-blox M8 Concurrent GNSS LCC Module,
 TCXO, flash, SAW, LNA,
  Timepulse Configurable 0.25 Hz to 10 MHz
 
 
The kit include:
 
-  F450  Quadcopter Frame x1 (unassembled)
 
- Plastic landing gear X 1 
 
- Flysky i6 remote control with ia6 receiver x 1 (send as your choice)
 
-  APM2.8  Flight Contro x1  ( Striaght / side pin send at random)  
 
-  Absorber board x 1
 
-  NEO-M8N GPS X1 
 
-  Gps stander holder x1
 
-  Power Module x 1  
 
- 2212  920kv Motor x4 
 
- plastic motor protection x 4
 
- 9450 Propeller x4 (2 pair)
 
- 30A Simonk ESC With 3.5mm bullet  x 4
 
- battery belt
 
- servo cables x 5
 

 

 
- Not assembled, just a kit
 
 
F450
 

 

 

 

 

 

   aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()DSC_0217

aeProduct.getSubject()