DW ADS1980 1914 2212 2216 2820 Water cooled Brushless Outrunner Motor For RC 1700KV 3000KV 3200KV 3700KV Freeshipping

DW ADS1980 1914 2212 2216 2820 Water cooled Brushless Outrunner Motor For RC 1700KV 3000KV 3200KV 3700KV Freeshipping
  • Продавецwww.flimmer.com
  • Список ценUS $40.23piece
  • Продажная ценаUS $40.23piece
  • ДоставкаБесплатная доставка
  • Рейтинги4,7 (159)

Oписание продукта

 
Item Description
 
F450 frame Description:
 
Features:
Built from quality glass fiber and polyamide nylon.
Integrated PCB connections for direct soldering of your ESCs
Pre-threaded brass sleeves for all of the frame bolts.
Colored arms for orientation to keep you flying in the right direction.
Large mounting tabs on main frame bottom plate for easy camera mounting.
Easy assembly.
 
Specs:
Width: 450mm
Height: 55mm
Weight: 280g (w/out electronics)
Motor Mount Bolt Holes: 16/19mm
Wheelbase: 17.7in/450mm
 
Made by advanced engineering material,super strong & smooth
Kit(need you assemble yourself)
100% Brand new 
 
Recommended config (Not Included):
A2208 OR A2212 800KV~1100kv brushless motor x4 sets
ESC 15~25A X4 sets
1800MAH~3600mAh 3S LiPo battery X1 SETS
1045 OR 8045 Forward&Reverse propeller X4 SETS
 
S500 quadcopter frame Description:
 
- F450 upgrade quadcopter
- Learned arm design from DJI S800 EVO, and enhanced
- Good work with Gopro Hero 3 2 Axis brushless gimbal for FPV
- PCB Center plate with solder point
- Frame only, no electronic parts.
 
REPTILE 500 Alien Multi-copter 500mm Quadcopter Frame 
 
Features:
 
- Center lower plate: 1-4pcs 45 * 45mm flight control board (FF, kk, rabbit, pirate, MWC, etc.)
- With Extend board, the ESC parallel plates or 4-in-1 ESC can be installed on it.
- With mounting holes for Wireless Transmitter ,CCD,OSD,GPS antenna,special design for installing NAZA flight control , holes for tall landing skill.
- 2200 mAh battery can be fixed at the end of the lower plate.
- Center upper plate: with cross holes for mounting NAZA GPS and aluminum mounting plate (38 * 38/33 * 33) in front of it for FPV camera.
- Transmitter or remote control receiver and other components can be set at the end of the plate.
 
 
Specification:
 
- Wheelbase:500mm
- Min Arm distance:380mm
- Max Arm distance:480mm
- Material:Glassfiber+ ABS Plastic
- Color:Black
 

2212 920kv Motor

- Type : 22 x 12mm

- KV: 920rpm/V

- Voltage: DC 7-12V

 

 

30A simonk esc Specifications:

 

Cont Current: 30A

Burst Current: 35A

BEC Model: Linear mode

BEC Output: 5V  2A

Li-ion/Li-poly:2-4S,or Ni-MH/Ni-Cd:4-12NIMH

Size: 32*24*7mm

 

Super high refresh rate, no buffering of the input signal, resulting in more than 490Hz response rate.

16KHz motor frequency, giving fastest response of the motor, and quietest operation as well (no 8KHz squeal).

 

Pixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller

 
Features:
 
1. The advanced 32-bit ARM CortexM4 high-performance processors, can run NuttX RTOS real-time operating system;
2. 14 PWM / servo output;
3. Bus interface (UART, I2C, SPI, CAN);
4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;
5. Provide automatic and manual modes;
6. Provide redundant power input and failover;
7. Multicolor LED lights;
8. Provide multi-tone buzzer Interface
9. Micro SD recording flight data;
 
Specifications:
 
Microprocessor
 
1.32 2 MB flash STM32F427 Cortex M4, with hardware floating-point processing unit
2. frequency: 168MHZ, 256K RAM
3.32 STM32F103 backup coprocessor
 
Sensor
 
1.L3GD20 3-axis digital gyroscope 16
2.LSM303D 3-axis accelerometer 14 / Magnetometer
3.MPU6000 6-axis accelerometer / magnetometer
4.MS5607 precision barometer
 
Interface
 
1 .5 high voltage compatible UART 1, 2 with hardware flow control
2. 2 CAN
3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input
4.Futaba SBUS compatible inputs and outputs
5.PPM Signal Input
6.RSSI (PWM or voltage) Input
7.I2C
8.SPI
9.3.3 and 6.6VADC input
10. External MICRO USB Interface
 
Packing list:
 
Quadcopter frame kit x 1 set ( you need to assemble it by yourself)
Pixhawk 2.4.8  32bit ARM Flight Controllerx 1
Safety buttonx 1
Buzzer x 1 (two kinds of buzzer because of different production batch, send it at random)
4G TF card(IO firmware has written)  x1
Mini OSD x1
PPM x1
I2C x 1
Power module X1
M8N GPS × 1
Black GPS holder x 1
Cables
4pcs 2212 920kv motor (2pcs CW, 2pcs CCW)
4pcs 30A simonk ESC
4 pair 1045 propeller (2 pair black and 2pair red)
 
 
 
F450 frame with red and white arms, if you need other color, let me know when  you place the order;
X500 with all black arm and plastic landing gear;
S500 PCB with all black arm and carbon fiber landing gear(s500 Version 2;
S500 PCB with all black arm and plastic landing gaer(S500 version 1);
 
 
Note: the frame is unassembled verison, you need to assemble it by yourself.
 
              
 
 
Item Pictures
 
F450 frame kit (10)
 
 
s500 pcb versions500 with carbon fiber landing gear
X500 with landing gear (11)
 
 
S500 pixhawk 2.4.8 M8N
 
 
note